|
DESCRIPTION
ALCO Tri-County Brush-On
is a liquid blend of solvent, refined cutback asphalt and non-asbestos
fillers that provide an elastic and durable coating for a superior
dampproofing application. This material, however, will not stand up to
hydrostatic pressure.
USE
Ideal for
reducing dampness and moisture infiltration through foundation walls,
footings, retaining walls, tanks, culverts and bridge abutments.
Installation of protection board is recommended before backfilling to protect
dampproofing application.
ADVANTAGES
»
Easy
Application » Ready to Use » Fast and economical way to protect concrete and
masonry foundations from moisture penetration
PREPARATION
The surface being covered must be clean, dry and
free from oil, form release agents and any foreign matter such as dust,
dirt, etc. Be sure all voids, cracks and rod holes are repaired with
fabric membrane. This material will not span large cracks. Use ALCO
Tri-County Trowel-On or ALCO 24/7 Flashing Cement and a fabric membrane
where applicable. Any repairs should be made before application.
APPLICATION
Use
a soft bristled brush and apply this material at a rate of 35 SF/Gal,
depending on the surface being coated. Porous surfaces may decrease
coverage. Under certain conditions, a cloth membrane can be used in a two
coat application. The first coat can be brushed on at about 35 SF/Gal.
Roll the fabric membrane into the first application, overlapping edges
approximately 3 - 4 inches, pressing firmly into place. Apply a second
coat of Tri-County Brush-On within two days.
COLD WEATHER APPLICATION: For best coverage results, material should be
stored in a warm warehouse and applied at the temperature of 40° F. or
above.
APPROXIMATE COVERAGE
35
SF/Gallon
SPECIFICATION
ASTM D-4479, Type
I
ASTM D-3019, Type III
VOC
Not to Exceed: 300 g/L 2.5 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
Not for use on wood * For professional use
only * Being a solvent based material, some insulation boards
may not be compatible. Check with board manufacturer before
applying.
PROPERTIES
Flash Point (ASTM
D-93-99): 100° F. Minimum
Weight per Gallon (Approximate): 8.0 Lbs
Viscosity @ 77° F. (ASTM D-562): 30 - 60 KU
Non-Volatile (Fed Test Method 141): 62% Minimum
Percent of Specially Processed Asphalt: 58% Minimum
Film Thickness of 50 SF/Gal (Less Absorption by Surface): 1/32"
Drying Time (to touch): 2 -3 Days
Service Temperature, Extended Exposure: -20° to 150° F.
Resistance to Oils & Solvents: Poor
Resistance to Sunlight: Good
Resistance to Chemicals: Good
Effect of Weathering: Slight Chalking
Resistance to Water:
Under Good Drainage Conditions:
Excellent
Under Continuous Submersion:
Not Recommended
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillates
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators
required if TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Chemical resistant gloves
such as neoprene are recommended. Do not get in eyes; splash proof goggles
are recommended. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat, open flame or
any source of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash thoroughly with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get medical
attention immediately. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
Spill or Leak: Shut off ignition source; no open flame. Stop leak
without risk. Dike area of spill and take up with sand or other suitable
material. Prevent from entering drains, sewers or waterways.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|