|
DESCRIPTION
ALCO Fibered Emulsion Dampproofing
consists of a non-asbestos fiber filled, emulsified asphalt with a clay
base. It is designed to be sprayed or brushed directly to masonry block or
poured concrete walls. It provides a thick, extremely smooth dampproof
coating for below grade applications.
USE
Ideal for
reducing dampness and moisture infiltration through foundation walls,
footings, retaining walls, tanks, culverts and bridge abutments.
Installation of protection board is recommended before backfilling to protect
dampproofing application.
ADVANTAGES
* Easy application -
Spray or Brush * Ready to use from the container *
Fast & economical way to protect concrete and
masonry foundations from moisture
penetration * Can be applied on "green" concrete
PREPARATION
The
surface being coated must be clean and free of oils, form release agents,
dust, dirt, etc., that may interfere with the adhesion of this product.
This material will not span large cracks. All voids, cracks and rod holes
must be repaired before application. Use ALCO 24/7 Flashing Cement and
membrane where applicable. Material may be applied on damp surfaces but
should not be attempted if rain is imminent.
APPLICATION
Stir
material to even consistency and color. Emulsion type dampproofing is the
breather-type which permits moisture vapor to escape through the film,
while remaining resistant to water penetration. This prevents blistering
of applied film, while remaining resistant to water penetration. This
material can be applied to green concrete (not totally dry).
BRUSH: Using a soft bristle brush apply in a continuous, unbroken film,
free of pinholes and over exposed footings, slots or grooves, etc.
SPRAY: Use Graco 9:1 ratio pump or equal, capable of delivering 3 - 5
gallons per minute and a pole gun with a 3/32" tip. A 3/4" I.D.
material hose and a 1/2" I.D. air hose from the pump to the gun is
preferred for most applications.
Allow 2 days to cure before backfilling.
APPROXIMATE COVERAGE
One Coat
Application 40 SF/Gallon
Two Coat Application 100 - 200 SF/Gallon
Coverage may be less, depending on the porosity of the surface being
covered.
SPECIFICATION
ASTM
D-1227, Type II, Class 1
PACKAGING
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
PROTECT FROM FREEZING * For outdoor use only *
Do not use on wood * Do not thin this material *
For
professional use only * This material is compatible with most insulation boards. Check with
board manufacturer before applying. * If winter storage is
necessary, maintain temperatures at 50° F. or above. Keep material off floor.
* Secure cover when not in use * Will not stand up to hydrostatic pressure
PROPERTIES
Weight per Gallon (Approximate):
8.3 Lbs
Percent Non-Volatile (Fed Test Method
141): 50% +
Percent of Asphalt: 45% +
Percent of Total Solids, by Volume: 53% +
Viscosity: 10,000 - 15,000 cps
Ash on Basis of Non-Volatile Material: 5% Minimum
Penetration of Base Asphalt (ASTM D-5): 60 - 100
Flash Point of Base Asphalt, C.O.C. F: 450 +
Ductility of Base Asphalt: 100 +
Film Thickness of 1 Gal/25 SF (Less Absorption by Surface): 1/16"
FOR FURTHER SAFETY INFORMATION
SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution
Contains Petroleum
Hydrocarbons
Hazard Rating: Health
- 1 Fire - 0 Reactivity -
0
(0 = Least; 4 = Extreme)
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes;
wear protective goggles or face shield. Wear protective clothing if needed.
Do not take internally.
Fire Protection: Non-flammable
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash with waterless hand cleaner and/or
soap and water. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|