|
DESCRIPTION
ALCO Foundation Mastic
Rubberized is a compound of high quality asphalt, rubberizing agents and
select non-asbestos fillers. It is a heavy-duty elastomeric which cures to
a tough, waterproof barrier.
USE
: Efficient
waterproofer : Provides excellent waterproofing
efficiency : Provides excellent waterproofing protection to
exterior surfaces below grade : Recommended for waterproofing
below grade walls of poured concrete and/or masonry block
construction : Provides superb corrosion protection for
metal
ADVANTAGE
» Ready to use
from the container » Provides continuous, flexible film
without cracks or pinholes » Excellent adhesion to concrete,
masonry and steel » Resistant to lime, gypsum and ground and
airborne chemicals
PREPARATION
Before coating, surface to be coated must be
fully cured. Surface area must be smooth, clean, dry and free from oil,
form release agents, loose scaling, rust, dirt, dust and debris. Be sure
all voids, cracks and rod holes are repaired. This material will not span
large cracks. Use ALCO 24/7 Flashing Cement and a fabric membrane where
applicable. All repairs must be done before application.
APPLICATION
This material was developed for spray application, but may be applied with
a brush. If spraying, use a Graco 40:1 pump or equivalent. When brushing,
be sure to brush in one direction only to avoid air pockets and pin holes.
For best results, apply when temperature is 40° - 90° F. If temperature
is below 40° F, or humidity is above
80%, the material could take longer to cure. For optimum results, the
recommended dry thickness is 40 - 60 mils.
Do not backfill for at least 24 hours after application.
Backfill within 7 days. Backfill should be placed in a manner that will
not rupture or damage the film or displace the coating or membranes.
NOTE: Installation of protection board is recommended before backfilling
to protect waterproofing application. Call for recommendations and
warranty information.
APPROXIMATE COVERAGE
40 Mils
Dry 25 SF/Gallon
SPECIFICATION
ASTM D-4586, Type
I
VOC
Not to Exceed: 367 g/L 3.1 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
55 Gallon Drum 4/Pallet
LIMITATIONS
*
For professional use
only * Do not use on wood surfaces * Being a solvent based material, some insulation boards
may not be compatible. Check with board manufacturer before
applying.
PROPERTIES
Flash Point (ASTM
D-93-99): 100° F. Minimum
Weight per Gallon (Approximate): 8.0 Lbs
Viscosity @ 77° F. Kinematic, Winter Grade: 90 - 100 cps
Non-Volatile (Fed Test Method 141): 62% Minimum
Percent of Specially Processed Asphalt: 58% Minimum
Percent of Total Solids, by Volume: 58% Minimum
Drying Time (to touch): 2 -3 Days
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillates
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators
required if TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Chemical resistant gloves
such as neoprene are recommended. Do not get in eyes; splash proof goggles
are recommended. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat, open flame or
any source of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash thoroughly with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get medical
attention immediately. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
Spill or Leak: Shut off ignition source; no open flame. Stop leak
without risk. Dike area of spill and take up with sand or other suitable
material. Prevent from entering drains, sewers or waterways.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|