|
DESCRIPTION
ALCO Fiber Roof Coating
is a superior blend of asphalt, solvents and non-asbestos fiber fillers.
Those fillers thicken the liquid asphalt to form a tough and elastic
surface.
USE
: Excellent as a
protective coating on metal, smooth BUR, SBS Modified Bitumen membrane and
roll roofing
ADVANTAGES
» Easy
Application - Brush or Spray » Ready to use from the
container » No heating or thinning » Fast and economical way to protect
a flat roof
PREPARATION
Roof surface and all parapets should be swept
clean of all dust and dirt. All repairs should be done before coating,
with cotton membrane, fiberglass mat or ALCO Poly-S and either ALCO 24/7
Flashing Cement or ALCO Plastic Roof Cement.
NOTE: Install on roofs and decks with positive drainage. The National
Roofing Contractors Association's observation is as follows: "The
criteria for judging proper slope for drainage is there be no evidence of
standing water on the deck 48 hours after it stops raining."
APPLICATION
After
surface has been cleaned and repaired, Fiber Roof Coating can be applied
directly from the container. Do not thin or apply like paint. Be sure to
fill in all hairline cracks and crevices insuring a uniform coat over the
entire roof surface.
BRUSH: Apply with a soft bristle brush. Pour directly from the container
and spread evenly, brushing in one direction only.
SPRAY: Use airless equipment or a standard type mastic pump and apply a
smooth and even coat.
APPROXIMATE COVERAGE
Spray:
40 - 50 SF/Gallon
Brush: 40 - 50 SF/Gallon
SPECIFICATION
ASTM D-4479, Type
I
VOC
Not to Exceed: 300 g/L 2.5 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
1 Gal
Can
6/Carton
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
Do not use on wood surfaces * Do not use on
surfaces previously coated with Coal Tar * For professional
use only * Do not thin this material * May not be
compatible with some one-ply systems. Check with manufacturer of roof
system before application * For flat roofs only
PROPERTIES
Flash Point (ASTM
D-93): 100° F. +
Weight per Gallon (Approximate): 8.1 Lbs +
Viscosity @ 77° F. (ASTM D-562): 30 - 60 KU
Non-Volatile (Fed Test Method 141): 50% +
Percent of Filler: 5% - 20%
Percent of Specially Processed Asphalt: 40% +
Percent of Total Solids, by Volume: 58% Minimum
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface): 1/64"
Drying Time: 2 -3 Days
Service Temperature, Extended Exposure: -20° to 150° F.
Resistance to Oils & Solvents: Poor
Resistance to Chemicals: Good
Resistance to Sunlight: Good
Effect of Weathering: Slight Chalking
Resistance to Water:
Under Good Drainage Conditions:
Excellent
Under Continuous Submersion:
Not Recommended
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillates
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA approved
respirators
required if TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Wear chemical resistant gloves.
Do not get in eyes; splash proof goggles recommended. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat, open flame and
any source of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash thoroughly with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get medical
attention and keep victim warm. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|