|
DESCRIPTION
ALCO Fibered Asphalt Emulsion
Roof Coating consists of a specially formulated asphalt, an emulsifying
agent, clay filler, with non-asbestos fibers for brush or spray
application.
USE
: Economical protective coating for BUR, metal or
roll roofing
ADVANTAGES
» Easy application » Ready to use from the container
» Capable of bonding on damp surfaces (not wet) » No
heating or thinning » Fast and economical way to
coat roof deck
PREPARATION
Roof surface and all parapets should be swept
clean of all dust and dirt. All repairs should be done before coating,
using a cotton or fiberglass membrane or ALCO Poly-S, along with ALCO
Plastic Roof Cement, ALCO Wet-Bond Cement or ALCO 24/7 Flashing Cement.
A primer coat should be used under emulsion roof coating. If primer coat
is not used, surface to be coated should be thoroughly hosed down with a
high pressure hose and scrubbed with a stiff broom.
APPLICATION
Stir
material to even consistency and color.
For best results, apply when the temperature is 50° F. and rising, with
no rain forecasted within 24 hours. Allow 4 - 8 hours drying time under
normal drying conditions. For effective cure, allow 2 days.
BRUSH APPLICATION: Apply with a soft bristle brush. Pour material directly
from the container and brush to a smooth and even coat.
SPRAY APPLICATION: Use a standard type mastic pump.
APPROXIMATE COVERAGE
Brush
Application 40 - 50 SF/Gallon
Spray Application 40 - 50 SF/Gallon
SPECIFICATION
ASTM
D-1227, Type II, Class 1
PACKAGING
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
PROTECT FROM FREEZING * For outdoor use only *
For
professional use only * Do not thin this material *
Do not use on wood * If winter storage is
necessary, maintain temperatures at 50° F. or above. Keep material off floor.
* Secure cover when not in use
PROPERTIES
Weight per Gallon (Approximate):
8.3 Lbs
Percent Non-Volatile (Fed Test Method
141): 50% +
Percent of Asphalt: 45% +
Percent of Total Solids, by Volume: 53% +
Viscosity: 10,000 - 15,000 cps
Ash on Basis of Non-Volatile Material: 5% Minimum
Penetration of Base Asphalt (ASTM D-5): 85 - 100
Flash Point of Base Asphalt, C.O.C. F: 450 +
Ductility of Base Asphalt: 100 +
Film Thickness of 1 Gal/50 SF (Less Absorption by surface): 1/32"
FOR FURTHER SAFETY INFORMATION
SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution
Contains Petroleum
Hydrocarbons
Hazard Rating: Health
- 1 Fire - 0 Reactivity -
0
(0 = Least; 4 = Extreme)
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes;
wear protective goggles or face shield. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Non-flammable
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash with waterless hand cleaner and/or
soap and water. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|