|
DESCRIPTION
ALCO Resurfacer Cold
Process Adhesive is made of quality refined cutback asphalt and
non-asbestos fillers and bonders. It assures a rapid, tight bond similar
to a blind nail or a lap cement with prepared rolled roofing.
USE
This
material is widely used in cold process roofing systems and with many
manufactured coated fiberglass felts and base sheets. It is a general
purpose lap and ply cement for sealing laps of mineral surface rolls,
smooth surface roofing and base sheets.
ADVANTAGES
»
Easy
Application » Ready to use from the
container » Multi-purpose Adhesive » Brush or
Spray Application
PREPARATION
Surface to be repaired must be clean, dry and
free from oil, grease, dirt, loose coatings or other foreign matter that
may impede adhesion.
APPLICATION
When using mineral
surface rolls, smooth surface roofing or base sheets, pour Resurfacer
directly from the container and spread approximately 1/16" thick,
using a soft bristle brush or squeegee.
APPROXIMATE COVERAGE
Brush:
40 SF/Gal
Spray: 60 SF/Gal
SPECIFICATION
ASTM D-4479, Type
I
VOC
Not to Exceed: 300 g/L 2.5 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
1 Gal
Can
6/Carton
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
Not for use on wood surfaces * For professional use
only * Do not use on surfaces previously coated with Coal
Tar * May not be
compatible with some one-ply systems. Check with manufacturer of roof
system before application
PROPERTIES
Flash Point (ASTM
D-93): 100° F. +
Weight per Gallon (Approximate): 8.1 Lbs
Viscosity @ 77° F. (ASTM D-562): 60 - 130 KU
Non-Volatile (Fed Test Method 141): 50% +
Percent of Filler: 5% - 20%
Percent of Specially Processed Asphalt: 40% +
Percent of Total Solids, by Volume: 58% +
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface): 1/64"
Drying Time: 2 -3 Days
Service Temperature, Extended Exposure: -30° to 150° F.
Resistance to Oils & Solvents: Poor
Resistance to Chemicals: Good
Resistance to Sunlight: Good
Effect of Weathering: Slight Chalking
Resistance to Water:
Under Good Drainage Conditions:
Excellent
Under Continuous Submersion:
Not Recommended
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillates
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA approved
respirators
required if TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Wear chemical resistant gloves.
Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat, open flame and
any sources of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get
emergency
medical
attention and keep victim warm. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|