|
DESCRIPTION
ALCO Plastic Roof Cement
is made of quality refined asphalt, solvents and NON-asbestos fillers and
is ready to use from the container. It is manufactured to a heavy bodied
consistency for trowel application. Dries to an extremely tough but
flexible waterproofing membrane layer.
USE
: Patching of cracks and breaks in roof
surfaces : Flashing around skylights, chimneys, vents and
gutters
ADVANTAGES
» Easy
Application » Ready to use from the container »
Manufactured in Summer, Spring/Fall and Winter Grades »
Excellent adhesion to many common roof surfaces » Spreads to
a smooth, trowel consistency which will adhere without sagging
PREPARATION
The surface being coated must be clean, dry and
free from oil, grease, dirt, loose coatings or other foreign matter.
APPLICATION
Apply Plastic Roof Cement with a standard trowel or putty knife. On
small hairline cracks, fill the crack and feather down all edges. On
larger cracks or voids, it may be necessary to use a fabric membrane with
this material. Apply Plastic Roof Cement approximately 1/4" thick to
repair area, then embed membrane directly into cement. Apply another coat
of Plastic Roof Cement over membrane, feathering down all edges. Once
repair has been completed, surface can be coated with ALCO's many quality
roof coatings.
COLD
WEATHER APPLICATION: For best coverage results, material should be stored
in a warm warehouse and applied at the temperature of 40° F. or
above.
This product is formulated in three grades to accommodate seasonal
temperature ranges.
Summer
65 - 95 + 5 Degrees
Spring/Fall
40 - 65 + 5 Degrees
Winter
24 - 40 + 5 Degrees
APPROXIMATE COVERAGE
1/8"
Film
12.5 SF/Gallon
1/4"
Film
6.25 SF/Gal
SPECIFICATION
ASTM D-4586, Type
I
Fed Spec SS-C 153, Type I (Non-Asbestos)
VOC
Not to Exceed: 300 g/L 2.5 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
1 Gallon Can 6/Carton
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
Do not use on wood surfaces or roofs previously coated with Coal Tar
* For professional use
only * May not be compatible with some one-ply systems, such
as EPDM. Check with the manufacturer of roof system before application
PROPERTIES
Flash Point (ASTM
D-93-99): 100° F. +
Weight per Gallon (Approximate): 8.5 Lbs
Non-Volatile (Fed Test Method 141): 70% Minimum
Percent of Specially Processed Asphalt: 35% to 65%
Mineral and/or Other Stabilizers: 15% - 40%
Percent of Total Solids, by Volume: 65% +
Film Thickness of 1 Gal/12.5 SF: 1/8"
Drying Time: 2 -3 Days
Service Temperature, Extended Exposure: -40° to 180° F.
Resistance to Oils & Solvents: Poor
Resistance to Sunlight: Excellent
Resistance to Chemicals: Good
Effect of Weathering: Slight Chalking
Resistance to Water:
Under Good Drainage Conditions:
Excellent
Under Continuous Submersion:
Not Recommended
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillates
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators
required of TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Wear chemical resistant gloves.
Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat, open flame or
any sources of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get emergency
medical
attention and keep victim warm. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|