|
DESCRIPTION
ALCO Black Caulking
Mastic is a superior blend of the highest quality of refined asphalt,
including an excellent non-asbestos filler, solvents and hydrocarbons. A
very unique process is used to open the filler, providing a very smooth
homogeneous consistency not found in any standard mastic.
USE
: General Roof Repair : Pointing
: Flashing of parapet walls : Joint filler in a low, non-tracking area : Between foundation and sills of metal
buildings
ADVANTAGES
» Easy
Application » Multi-purpose » Ready to Use
PREPARATION
Surface being repaired should be clean, dry and
free from oil, grease, dirt, loose coating or other foreign matter.
APPLICATION
Material is applied directly from the container. On small hairline
cracks, feather down the edges with a trowel. On larger cracks or voids,
it may be necessary to use a membrane cloth with this material. After
repair has been made, coat entire area with ALCO Fiber Roof Coating.
TUBE APPLICATION: Use with large caulking gun. Cut tip to job
specifications.
COLD
WEATHER APPLICATION: Keep material at room temperature before using.
APPROXIMATE COVERAGE
13.6 LF @ 3/8" Bead
SPECIFICATION
ASTM D-4586, Type
I
VOC
Not to Exceed: 300 g/L 2.5 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
30 Oz Tube 12/Carton
LIMITATIONS
* Do not use on wood surfaces * For professional use
only * Do not use on roofs previously coated with Coal
Tar * May not be compatible with some one-ply systems. Check
with the manufacturer of roof system before application
PROPERTIES
Flash Point (ASTM
D-93): 100° F. +
Weight per Gallon (Approximate): 8.5 Lbs +
Non-Volatile (Fed Test Method 141): 70% Minimum
Percent of Specially Processed Asphalt: 35% to 65%
Mineral and/or Other Stabilizers: 15% - 40%
Percent of Total Solids, by Volume: 65% +
Film Thickness of 1 Gal/12.5 SF: 1/8"
Drying Time: 2 -3 Days
Service Temperature, Extended Exposure: -40° to 180° F.
Resistance to Oils & Solvents: Poor
Resistance to Sunlight: Excellent
Resistance to Chemicals: Good
Effect of Weathering: Slight Chalking
Resistance to Water:
Under Good Drainage Conditions:
Excellent
Under Continuous Submersion:
Not Recommended
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillates
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators
required of TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Chemical resistant gloves
such as neoprene are recommended.. Do not get in eyes; splash proof goggles
are recommended. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat, open flame or
any sources of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash thoroughly with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get medical
attention immediately. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
Spill or Leak: Shut off ignition source; no open flame. Stop leak
without risk. Dike area of spill and take up with sand or other suitable
material. Prevent from entering drains, sewers or waterways.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|