VIEW THE MSDS

211

WET-BOND PLASTIC ROOF CEMENT

DESCRIPTION
ALCO Wet-Bond Plastic Roof Cement is a special blend of refined cutback asphalt, a special chemical bonder and non-asbestos fiber fillers. It is of heavy trowel consistency and can be applied to wet or dry surfaces. 

USE
Emergency repair of wet or damp roof surfaces 

ADVANTAGES
»  Adheres to wet surfaces  »  Easy application  »  Ready to use from the container  »  Excellent adhesion to many common roof surfaces  »  Adheres without sagging  »  Produced in Summer, Spring/Fall and Winter grades 

PREPARATION
Before application, be sure area to be repaired is free from dirt, grease, oil and debris. Be sure that all standing water, ice and snow are swept away from repair area. A cloth membrane may be needed to repair larger cracks. 

APPLICATION
Apply with a trowel or putty knife. On small hairline cracks, fill the cracks and feather down all edges. On larger cracks or voids it may be necessary to use a membrane cloth. Apply material at approximately 1/4" thickness, imbedding the membrane directly into the cement and making sure to feather down all edges. Once repair has been completed, coat the entire surface with ALCO Wet-Bond Fiber Coating.
For ease of application in cold weather, keep material at room temperature before use. 
When applying this material during inclement weather, it is advisable to inspect the job when better working conditions return. 

COVERAGE
1/8" Film            12.5 SF/Gallon 
1/4" Film            6.25 SF/Gallon 

SPECIFICATION
ASTM D-4586, Type I 

VOC
Not to Exceed:  300 g/L  2.5 Lbs/Gal 
                    FOR OUTDOOR USE ONLY 
                 DO NOT THIN THIS PRODUCT
             SECURE COVER WHEN NOT IN USE

PACKAGING
1 Gallon Can         6/Carton
5 Gallon Pail        36/Pallet
55 Gallon Drum     4/Pallet

LIMITATIONS
* Not for use on wood  *  For professional use only  *  Not compatible with roofs coated with Coal Tar  *  May not be compatible with some roof systems. Check with manufacturer before application

PROPERTIES
Flash Point (ASTM D-93): 100° F. + 
Weight per Gallon (Approximate): 8.5 Lbs
Non-Volatile (Fed Test Method 141): 70% Minimum 
Percent of Specially Processed Asphalt: 35% to 65%
Mineral and/or Other Stabilizers: 15% - 40%
Percent of Total Solids, by Volume: 65% + 
Film Thickness of 1 Gal/12.5 SF: 1/8"
Drying Time: 2 -3 Days
Service Temperature, Extended Exposure: -40° to 180° F.
Resistance to Oils & Solvents: Poor 
Resistance to Sunlight: Excellent 
Resistance to Chemicals: Good
Effect of Weathering: Slight Chalking
Resistance to Water:
        Under Good Drainage Conditions: Excellent
        Under Continuous Submersion: Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution   Combustible 
Contains Petroleum Distillates 
Hazard Rating: Health - 1    Fire - 2    Reactivity - 0 
                           (0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA Respirators required if TLV is exceeded. 
Personal Protection: Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take internally.
Fire Protection: Keep away from heat, open flame or any sources of ignition.  
First Aid: Eye Contact - Rinse immediately with water for 15 minutes and seek medical advice. Skin Contact - Wash with soap and water. Inhalation - Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get emergency medical attention and keep victim warm.  Ingestion - Do not induce vomiting. Get medical attention immediately.
Waste Disposal: Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.
                            KEEP OUT OF REACH OF CHILDREN!