VIEW THE MSDS

215

ALUMAGARD
Fibered Aluminum Roof Coating

DESCRIPTION
ALCO Alumagard Fibered Aluminum Roof Coating consists of a high quality oxidized cutback asphalt, non-asbestos fiber fillers and premium quality aluminum pigments which flake and float to the surface upon application.  

USE
:  Excellent over metal roofs  :  Recommended for asphalt roofs and Modified Bitumen Membrane 

ADVANTAGES
»  Lowers surface temperature of roof by as much as 15° F.  »  Can turn away over 70% of harmful UV rays  »  Easy Application  »  Excellent Coverage  »  Economical  »  Premium 3# performance  »  UL Approved  »  FM Approved  »  Energy Star Partner   

PREPARATION
The roof surface must be completely dry and free of dirt, dust and debris before application. Be sure that all necessary repairs are done to the roof surface. Be sure metal surfaces are wire brushed and swept clean. This will ensure proper adhesion. In some cases ALCO Primer may be advisable. Allow primer to dry for 24 hours before aluminum application. ALCO 24/7 Flashing Cement or Plastic Roof Cement can be used to repair flashing, blisters or voids. 

APPLICATION
Use directly from the container. Mix contents thoroughly to insure complete dispersion of aluminum pigments. DO NOT THIN. Pour Alumagard Fibered coating on roof, a little at a time, and brush like any roof coating, brushing in one direction only. Over brushing causes some of the aluminum sheen to lessen, resulting in inferior reflective qualities. 
For best results, apply on a warm (60° F), sunny day with no rain in the forecast. The presence of moisture will create a rapid "browning out". The warm temperatures will soften the asphalt content and allow the aluminum pigments to rise to the surface for maximum reflectivity.
New asphalt roof surfaces should weather a minimum of 90 days before applying Alumagard. However, Alumagard may be applied over ALCO emulsion roof coatings after curing (between 5 - 10 days) without staining. 

APPROXIMATE COVERAGE
BUR:         50 -  75 SF/Gallon
Metal:       75 - 125 SF/Gallon 
APP:         50 - 100 SF/Gallon 

SPECIFICATION
ASTM D-2824, Type III 

VOC
Not to Exceed:  500 g/L  4.0 Lbs/Gal 
                    FOR OUTDOOR USE ONLY 
                 DO NOT THIN THIS PRODUCT
             SECURE COVER WHEN NOT IN USE

PACKAGING
1 Gal Can             6/Carton
5 Gallon Pail        36/Pallet
55 Gallon Drum     4/Pallet

LIMITATIONS
* Do not use over wood  *  Not compatible with roofs coated with Coal Tar  *   For professional use only  *  Will not adhere to wet or damp roof  *  Do not use if rain is in the forecast  *  On new, single-ply roofs, always check with the manufacturer of the roofing system for compatibility with this product  *  Not recommended for ponded water   

PROPERTIES
Flash Point (ASTM D-93): 100° F. + 
Weight per Gallon (Approximate): 8.8 Lbs 
Viscosity @ 77° F. (ASTM D-2824):  15 - 90 KU
Percent of Specially Processed Asphalt:  25% +
Percent of Metallic Aluminum Leafing Paste:  25% +
Percent of Solids, by Weight:  40% 
Type Aluminum Paste: 
     TT-P-320-D, Type II:  Class 2
     ASTM D-962, Type II:  Class C
Insoluble in CS2, Maximum % of NVM:  50%
Non-Volatile Matter (NVM):  40% Minimum
Film Thickness of 100 SF/Gallon (Less Absorption by Surface): 1/64"
Reflectivity (ASTM Requirement):  50% +
Actual Reflectivity (Averaged): 
     Initial:  68.1% 
     Aged:  71.1%
Drying Time: Overnight 
Service Temperature, Extended Exposure:  -20° to 180° F.
Resistance to Oils & Solvents: Poor 
Resistance to Chemicals: Poor 
Resistance to Sunlight:  Excellent
Effect of Weathering: Slow Erosion 
     Acid Rain & Corrosive Atmospheric Conditions will Discolor or Darken
Resistance to Water:
        Under Good Drainage Conditions: Excellent
        Under Continuous Submersion: Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS

Caution   Combustible 
Contains Petroleum Distillates 
Hazard Rating: Health - 1    Fire - 2    Reactivity - 0 
                           (0 = Least; 4 = Extreme)
NOTE: DO NOT THIN. DO NOT MIX WITH WATER, ACIDS OR ALKALIS
Respiratory: Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA approved respirators required if TLV is exceeded. 
Personal Protection: Avoid prolonged or repeated contact with skin, which may cause irritation. Wear chemical resistant gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take internally.
Fire Protection: Keep away from heat, open flame and any sources of ignition.  
First Aid: Eye Contact - Rinse immediately with water for 15 minutes and seek medical advice. Skin Contact - Wash with soap and water. Inhalation - Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get emergency medical attention and keep victim warm. Ingestion - Do not induce vomiting. Get medical attention immediately.
Waste Disposal: Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.
                      KEEP OUT OF REACH OF CHILDREN!

WARRANTY
We warrant our materials to be of good quality and will replace materials found defective, providing, however, that the buyer shall examine the materials when received and promptly notify us of any defects before the materials are used or incorporated into a structure for which they are intended. Unless otherwise agreed to in writing, this warranty shall extend only to comply with specifications of materials manufactured by and published by ALCO-NVC Inc., and made available to the buyer at request. We cannot warrant nor in any way guarantee particular methods, use or applications, nor can we warrant that the materials will be suitable for any intended use. This warranty is in lieu of all others expressed or implied and may not be extended by representatives, written sales or information or drawings. Nor do our distributors or salesmen or any other representatives of distributors or of this  company have any authority to extend any guarantee beyond that outlined above or to waive the limitations of the seller's liability.


Give us a call at (800) 323-0029, we'll tell you even more!

ALCO NVC
ALCO-NVC Inc.   580 St. Jean   Detroit, MI 48214-0001
Toll Free: (800) 323-0029   Fax: (313) 331-4726



HOME | ABOUT US | PRODUCTS | SYSTEMS | MSDS | CONTACT | REQUEST


© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY:
DIVERSIFIED COMPUTER SERVICES, INC.