|
DESCRIPTION
ALCO White Patching
Cement is processed with acrylic elastomeric resin, titanium dioxide white
pigment and special reinforcing fibers. It is a resilient, long lasting
and durable patch that provides premium protection withstanding the sun's
rays. This product also provides excellent resistance to mildew and
weathering.
USE
: Excellent for repairing metal, polyurethane foam
and masonry : Provides highly flexible, watertight seal over
seams, fasteners, around protrusions, skylights, vents, flashings around
mounted equipment and any other suspected leak areas
PREPARATION
Surface must be power washed with a mild
detergent (except with new polyurethane foam) at a minimum of 2000 psi to
remove dirt, loose paint, dried out caulk and other foreign matter which
could prevent proper adhesion.
APPLICATION
Material is ready to use from the container and
requires little or no mixing. Apply with a brush, trowel or putty knife. May be applied over damp, not wet, surfaces.
To repair cracks and seams using polyester fabric, remove all dried out
and loosely adhered caulking and coating. Apply cement over entire length of seam or crack; apply 1" - 2" wider than the
polyester fabric. Embed fabric into cement, smoothing fabric carefully
without stretching. Apply second layer of cement, completely covering
fabric and ensuring that all edges and corners of the fabric are firmly
embedded.
Replace all missing fasteners and tighten existing screws or fasteners.
Severely rusted metal panels should be replaced.
NOTE: Vertical seams on standing seam metal roofs do not require patching.
FOR OUTDOOR USE ONLY
DO NOT
THIN THIS PRODUCT
SECURE COVER WHEN NOT IN
USE
COVERAGE
25 SF/Gallon @ 1/16" Thickness
(Depending on type and size of surface)
PACKAGING
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
Do not use on wood * For professional use only *
Do not apply when temperature is below 50° F. * Do not apply
when rain is in the forecast * High humidity will extend dry
time * Allow cement to dry a minimum of 4 hours before
exposure to rain, heavy dew or temperatures below 50° F. * PROTECT FROM FREEZING
PROPERTIES
Vehicle Base:
Acrylic Based Elastomeric Resin
Weight per Gallon: 10.5 Lbs + 0.02
Solids by Weight: 71 + 2%
Solids by Volume: 50 + 2%
Viscosity @ 80° F. (27° C.): Trowelable
Dry Film Thickness @ 25 SF/Gal or 30 LF/Gal: 32 Mils
(Less absorption by surface)
Dry Time:
Set to Touch: 1 - 2 Hours
To Apply Coating: 24 - 48 Hours
pH: 8.5 + 0.05
Specific Gravity: 1.127
Flash Point: None
Solvent: Water
Clean Up: Warm, soapy water
FOR FURTHER SAFETY INFORMATION
SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Hazard Rating: Health
- 1 Fire - 0 Reactivity - 1
(0 = Least; 4 = Extreme)
Respiratory:
Use with adequate ventilation. Inhalation of high vapor concentration may
cause headaches and/or dizziness. NIOSH/MSHA approved respirators required
if TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Wear chemical resistant gloves.
Do not get in eyes; wear protective goggles or face shield. Wear protective clothing if needed.
Launder clothing before reuse. Do not take internally.
Fire Protection: Keep away
from heat and open flame and any sources of ignition. Material in liquid
state is non-flammable. Dry polymer can burn.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get
emergency medical attention and keep victim warm. Ingestion -
Contact a physician immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|