VIEW THE MSDS

233

ASPHALT RESATURANT

DESCRIPTION
ALCO Resaturant consists of a blend of select asphalt, solvent, inorganic fillers, fibers and long and short penetrating oils. These penetrating oils soak into the existing felts to rejuvenate the old asphalt and felt. A coating of asphalt remains on the roof surface to protect the felt from the ultra-violet rays of the sun and will act as a binder for the replacement of the slag or gravel. 

USE
:  For built up roofs with slopes less than 2" per running foot  :  Revitalizes existing roofing felts  :  Adhesive to hold gravel on roofs  :  Provides a flexible, waterproofing barrier     

ADVANTAGES
»  Ready to use from the container  »  Economical way to extend life of roof     

PREPARATION
Surface to be repaired must be clean, dry and free from dirt, dust and debris. Remove all gravel/aggregates by sweeping or using a power broom. Repair all blisters, breaks and holes in the roof using ALCO 24/7 Flashing Cement and membrane cloth where needed. 

APPLICATION
Apply directly from the container with brush or conventional spray equipment. When brushing, be sure to brush in one direction. Fill in all hairline cracks and crevices ensuring a uniform coat over the entire roof surface. 

COVERAGE
Smooth Surfaces            4 - 5 Gal/Square
            (All gravel removed) 

SPECIFICATION
ASTM D-4479, Type I 

VOC
Not to Exceed:  300 g/L  2.5 Lbs/Gal 
                    FOR OUTDOOR USE ONLY 
                 DO NOT THIN THIS PRODUCT
             SECURE COVER WHEN NOT IN USE

PACKAGING
5 Gallon Pail        36/Pallet
55 Gallon Drum     4/Pallet

LIMITATIONS
* Do not use on wood surfaces  *  Do not use on surfaces previously coated with Coal Tar  *  For professional use only  *  May not be compatible with some one-ply roof systems. Check with manufacturer of roof system before application    

PROPERTIES
Flash Point (ASTM D-93): 100° F. Minimum
Weight per Gallon (Approximate): 8.1 Lbs 
Viscosity @ 77° F. (ASTM D-562): 60 - 130 KU
Non-Volatile (Fed Test Method 141): 50% +
Percent of Filler: 5% - 20%
Percent of Specially Processed Asphalt: 40% +
Percent of Total Solids, by Volume: 58% +
Film Thickness of 1 Gal/100 SF (Less Absorption by Surface): 1/64"
Drying Time: Several Days 
       (Depending on Weather; Material does not cure out hard)
Service Temperature, Extended Exposure: -30° to 150° F.
Resistance to Oils & Solvents: Poor 
Resistance to Chemicals: Good 
Resistance to Sunlight: Good
Effect of Weathering: N/A
Resistance to Water:
        Under Good Drainage Conditions: Excellent
        Under Continuous Submersion: Not Recommended

FOR FURTHER SAFETY INFORMATION SEE MSDS REGARDING THIS PRODUCT

PRECAUTIONS
Caution   Combustible 
Contains Petroleum Distillates 
Hazard Rating: Health - 1    Fire - 2    Reactivity - 0 
                           (0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor concentration may cause headaches and/or dizziness. NIOSH/MSHA approved respirators required if TLV is exceeded. 
Personal Protection: Avoid prolonged or repeated contact with skin, which may cause irritation. Chemical resistant gloves such as neoprene are recommended. Do not get in eyes; splash proof goggles are recommended. Wear protective clothing if needed. Do not take internally.
Fire Protection: Keep away from heat and open flame and any sources of ignition.  
First Aid: Eye Contact - Rinse immediately with water for 15 minutes and seek medical advice. Skin Contact - Wash thoroughly with soap and water. Inhalation - Remove individual to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration; get medical attention immediately. Ingestion - Do not induce vomiting. Get medical attention immediately.
Waste Disposal: Seal container when not in use. Empty containers must be disposed in an approved landfill in accordance with local, state and Federal regulations.
                      KEEP OUT OF REACH OF CHILDREN!