|
DESCRIPTION
ALCO 269 Plus is UL
approved and formulated from choice asphalts, solvents and non-asbestos
fillers. It is processed to a creamy smooth consistency for ease of
application. This material is specifically designed as a cold process
adhesive for adhering SBS modified membrane. When cured, its bonding
strength becomes as tough and elastomeric as the membrane itself.
USE
: Adheres SBS Modified Bitumen membranes - base
and ply sheets : Excellent conventional adhesive for BUR ply sheets
and granulated cap sheets
ADVANTAGES
» Easy Application »
Multi-purpose adhesive » UL approved » Ready to
use from the container » Elastomeric - moves with
substrate » Excellent resistance to water and
weather
PREPARATION
Surface to be adhered should be clean, dry and
free from oil, grease, dirt or any debris that will inhibit bonding
capabilities.
APPLICATION
Stir material before use. Material can be
brushed or notch squeegeed. The adhesive sets by the evaporation of the
solvent. Therefore, the adhesive should be allowed to cure for 5 - 15
minutes before membrane application for maximum adhesion. Temperature at
time of application should be above 40° F. and membrane temperatures
should not exceed 140° F.
Starting at the low end of the roof, apply material to the substrate
3" - 4" wider than the roll. Unroll membrane in the set
adhesive, making sure that it is laying flat. At the end laps, overlap
6" ensuring that the adhesive oozes out to bond at the end laps.
Continue application making sure the membrane overlaps 4" at the side
lap line. Roll all side laps and end laps, making sure a sufficient amount
of adhesive is applied to the laps so that a visible bead of adhesive is
present at the lap edges. Repeat above steps until roof surface is
covered.
COVERAGE
1-1/2 - 2 Gal/100 SF
SPECIFICATION
ASTM D-3019, Type III
VOC
Not to Exceed: 500 g/L 4.0 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
Do not use on wood * For professional use only
* Do not use with APP Torch Applied Modified Membranes *
Do not use on slopes greater than 1-1/2" with a 12" rise
* Do not use on surfaces previously coated with Coal Tar *
May not be
compatible with some one-ply roof systems. Check with manufacturer of roof
system before application
PROPERTIES
Flash Point (ASTM
D-93): 100° F. Minimum
Weight per Gallon (Approximate): 7.74 Lbs
Brookfield Viscosity @ 110° F. (#5 Spindle @ 20 RPM): 2000 - 3000
cps
Non-Volatile: 70% Minimum
Percent of Asphalt: 70% Minimum
Film Thickness of 100 SF/Gallon: 1/64"
Tack Time (Optimum weather): 30 - 60 Minutes
Total Cure Time: 30 Days (Approx)
Service Temperature: 40° to 150° F.
Resistance to Solvents: Poor
Resistance to Chemicals: Good
Resistance to Sunlight: Good
Effect of Weathering: Slight Alligatoring
Resistance to Water:
Not intended for use below
grade where hydrostatic pressure exists
ASTM Requirements: Strength of lap at indicated age, Lbs/In Width:
ASTM
269 Plus
At 60
Min.
8.0
#
28#
At 24
Hours
17.0#
117#
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillate
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA approved
respirators
required if TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Chemical resistant gloves.
Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat and open flame and
any source of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get medical
attention and keep victim warm. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|