|
DESCRIPTION
ALCO CAP Asphalt Mastic
is a superior blend of asphalt, solvents and non-asbestos fiber fillers.
The fillers in this product strengthen the liquid asphalt to form a tough
but elastic surface. Once cured, it will not track in summer or crack in
winter.
The coating is reinforced with mineral fibers which make it extremely
tough and weather resistant. It is especially designed for the CAP System.
It is recommended as a base and surface coating to be used in combination
with ALCO Poly-S, a stitchbond polyester. It provides an excellent re-roof
system to a wide range of roof areas, while adding years of service of the life of a roof.
USE
: Ideal for use with the CAP system
ADVANTAGES
» Excellent weather resistant
coating » Reinforced with fibers that form a tough but
elastic coating » Adds years of service to the life of the
roof
PREPARATION
Surface to be coated must be clean and dry.
Repairs must be done before coating is applied. All blisters, parapets and
protrusions should be repaired with ALCO 24/7 Flashing Cement or ALCO
Wet-Bond Cement.
APPLICATION
CAP Asphalt Mastic can be applied directly from
the container using a roof brush, squeegee or spray applicator. Do not
thin or apply like paint. Brush in one direction only. Be sure to fill all
hairline cracks and crevices to insure a uniform coat over entire roof
surface.
CAP SYSTEM: Using a 1, 2 or 3 ply method, brush, spray or squeegee mastic
on roof while embedding Poly-S into material and lap accordingly up roof
surface. Make sure to dry brush Poly-S to eliminate air pockets and
wrinkles. Then top coat with CAP Mastic.
NOTE: Keep in mind that Poly-S is 40" wide.
COVERAGE
2 - 2.5 Gal/100 SF
SPECIFICATION
ASTM D-4479, Type II
VOC
Not to Exceed: 300 g/L 2.50 Lbs/Gal
FOR OUTDOOR USE ONLY
DO NOT THIN THIS PRODUCT
SECURE COVER WHEN NOT IN USE
PACKAGING
5 Gallon Pail
36/Pallet
55 Gallon Drum 4/Pallet
LIMITATIONS
*
Do not use on wood * Not compatible with roofs
previously coated with Coal Tar * For professional use
only * Do not thin this material * May not be
compatible with some one-ply roof systems. Check with manufacturer of roof
system before application
PROPERTIES
Flash Point (ASTM
D-93): 100° F. +
Weight per Gallon (Approximate): 8.5 + .05 Lbs
Viscosity @ 77° F.: 50 - 100 cps
Non-Volatile (Fed Test Method 141): 50% +
Percent of Filler: 5% - 20%
Percent of Specially Processed Asphalt: 40% +
Percent of Total Solids, by Volume: 58% Minimum
Film Thickness of 1 Gallon/100 SF (Less absorption by surface):
1/64"
Drying Time: 2 - 3 Days
Service Temperature, Extended Exposure: -20° to 150° F.
Resistance to Oils and Solvents: Poor
Resistance to Chemicals: Good
Resistance to Sunlight: Excellent
Effect of Weathering: Slight Chalking
Resistance to Water:
Under Good Drainage Conditions: Excellent
Under Continuous Submersion: Not
Recommended
Not intended for use below
grade where hydrostatic pressure exists
FOR FURTHER SAFETY
INFORMATION SEE MSDS REGARDING THIS PRODUCT
PRECAUTIONS
Caution Combustible
Contains Petroleum
Distillate
Hazard Rating: Health
- 1 Fire - 2 Reactivity -
0
(0 = Least; 4 = Extreme)
Respiratory: Use with adequate ventilation. Inhalation of high vapor
concentration may cause headaches and/or dizziness. NIOSH/MSHA approved
respirators
required if TLV is exceeded.
Personal Protection: Avoid prolonged or repeated
contact with skin, which may cause irritation. Wear chemical resistant
gloves. Do not get in eyes; wear protective goggles. Wear protective clothing if needed. Do not take
internally.
Fire Protection: Keep away from heat and open flame and
any sources of ignition.
First Aid: Eye Contact - Rinse
immediately with water for 15 minutes and seek medical
advice. Skin Contact - Wash with soap and water. Inhalation
- Remove individual to fresh air. If breathing is difficult, administer
oxygen. If breathing has stopped, give artificial respiration; get emergency
medical
attention and keep victim warm. Ingestion - Do
not induce vomiting. Get medical attention immediately.
Waste
Disposal: Seal container when not in use. Empty containers must be
disposed in an approved landfill in accordance with local, state and
Federal regulations.
KEEP OUT OF REACH OF CHILDREN!
WARRANTY
We warrant our materials to be of good quality and will
replace materials found defective, providing, however, that the buyer
shall examine the materials when received and promptly notify us of any
defects before the materials are used or incorporated into a structure for
which they are intended. Unless otherwise agreed to in writing, this
warranty shall extend only to comply with specifications of materials
manufactured by and published by ALCO-NVC Inc., and made available to the
buyer at request. We cannot warrant nor in any way guarantee particular
methods, use or applications, nor can we warrant that the materials will
be suitable for any intended use. This warranty is in lieu of all others
expressed or implied and may not be extended by representatives, written
sales or information or drawings. Nor do our distributors or salesmen or
any other representatives of distributors or of this company have
any authority to extend any guarantee beyond that outlined above or to
waive the limitations of the seller's liability.
Give us a call at (800)
323-0029, we'll tell you even more!
ALCO-NVC Inc.
580
St. Jean Detroit, MI 48214-0001
Toll Free: (800)
323-0029 Fax: (313)
331-4726
HOME | ABOUT US |
PRODUCTS | SYSTEMS |
MSDS | CONTACT | REQUEST
© ALCO NVC, INC. ALL RIGHTS RESERVED. WEB SITE BY: DIVERSIFIED
COMPUTER SERVICES, INC.
|