MATERIAL SAFETY DATA SHEET
ALCO-NVC,
Inc Dated: July 10, 2007
PO BOX
14001 Reviewed: February 11, 2009
580 ST
JEAN 313-823-7500
DETROIT MI
48214 FAX:
313-331-4726
PRODUCT:
#601 Wood Cant Strip and
Tapered Edge
SECTION 1 PRODUCT IDENTIFICATION
Name: Fiberboard
Cant Strip and Tapered Edge
SECTION 2 INGREDIENTS
Name: % OSHA-PEL ACGIH-TLV COMMENTS
Cellulose < 95 5
5 mg/m3 Resp
CAS #9004-34-6
Starch < 9
5 5 mg/m3 Resp
CAS #9005-64-9
Clay 1
5 5 mg/m3 Resp
CAS # None
Carbon Black 1 3.5
3.5
mg/m3
CAS #1333-86-4
Wax 1 None
None
CAS # None
Lamination Adhesive 3.5 None None
CAS # None
CARCINOGENICITY: NTP LISTED IARC LISTED
OSHA REGULATED
Ingredient: None None
None
SECTION 3 PHYSICAL/CHEMICAL DATA
Boiling
Point: N/A
Vapor Pressure: N/A
Vapor
Density: N/A
Soluble in
Water: N/A
Specific
Gravity: 0.25 – 0.45
Percent
Volatiles: N/A
Evaporation
Rate: N/A
Appearance/Odor:
Brown Fiberboard; no odor
SECTION 4 FIRE & EXPLOSION
DATA
Flash
Point (Method): N/A
Upper
Explosive Limit: N/A
Lower
Explosive Limit: N/A
Special Fire
Fighting Procedures: None Known
Unusual
Fire & Explosion Hazards: May be
prone to smolder longer than wood after flames have been
extinguished.
NFTPA
Rating: 1 – Flammability 0 – Health 0 – Reactivity
(0 = Least;
4 = Extreme)
SECTION 5 REACTIVITY DATA
This
material is stable.
Conditions
to Avoid: None Known
Incompatibilities:
None Known
Hazardous
Decomposition Products: None Known
SECTION 6 HEALTH HAZARD DATA
Primary
Routes of Exposure: Inhalation if dust
is created during fabrication
Signs and
Symptoms of Overexposure:
Acute:
Temporary irritation of eyes, nose, throat, lungs
Chronic:
None Expected
Aggravated
Medical Conditions: Respiratory illness
NOTE: This
product is not expected to present health hazards under normal use.
SECTION 7 EMERGENCY & FIRST
AID PROCEDURE
Skin: Wash gently with soap and water.
Eyes: Flush with running water for 15 minutes.
Inhalation: Remove to fresh air.
Ingestion: N/A
SECTION 8 LEAK & SPILL
PROCEDURE
Steps to
be taken in case material is released or spilled: Normal housekeeping
Disposal
Method: In accordance with Federal,
state and local regulations.
KEEP OUT OF REACH OF
CHILDREN!
SECTION 9 CONTROL PROTECTION DATA
Ventilation: When fabricating use sufficient ventilation
to keep exposures below TLV
Respirator
Protection (Use only NIOSH Certified Device):
Dust mask during fabrication if necessary.
Protective
Clothing: Not normally necessary.
Eye
Protection: As necessary.
SPECIAL
PRECAUTIONS: Use of high speed rotary
cutting tools may create excessive dust. Avoid dust
inhalation through adequate
ventilation and the use of respiratory protection.
SECTION 10 USER RESPONSIBILITY
This
product material safety data sheet provides health and safety information. The
product is to be used in applications consistent with our product literature.
Individuals handling this product must be informed of the recommended safety
precautions and must have access to this information. For any other uses,
exposures must be evaluated so that appropriate handling practices and training
programs can be established to ensure safe work place operations. Please
consult your local sales representative for any further information.
SECTION 11 CLEAN UP AND DISPOSAL
Practice
good personal hygiene. Launder contaminated clothing before reuse. Use control
protection as necessary. Follow proper state and local regulations for disposal
of this product.
SECTION 12 DISCLAIMER
The
information set forth herein is believed to be accurate but is not warranted to
be, whether originating with ALCO-NVC, Inc or not. Recipients are advised to
confirm in advance of need that the information is current, applicable and
suitable to their circumstances.
This
Material Safety Data Sheet supersedes all other previously dated sheets for
this product.